Yorkville AP6040
판매가격 : 4,950,000
적립금 :0
제조사 :Yorkville
구매수량 :

제품특징

고효율과 최신의 회로기술로 제작된 AP시리즈 앰프들은 품질과 안전성 그리고 강력하고 완벽한 출력을 보장합니다.   
가장 선진화된 아나로그 파워 앰프 디자인으로 경량에 높은 출력의 AP 시리즈 앰프들은 PA 앰프의 새로운 기준을 보여줍니다.  

The most powerful Yorkville amplifier ever built. The three rack space AP6020 and AP6040 solve the problem of not having cost effective and practically configured power for subwoofers. With better than 2000W per channel (AP6020 @ 2 Ohms, AP6040 @ 4 Ohms), the AP6020 & AP6040 put plenty of clean power just where you need it. The incorporated 몊oft turn-on?circuit eliminates nuisance breaker-tripping on power-up while internal protection protects against DC output, thermal overload and inappropriate loads. The user defeatable limiter also prevents audible clipping.

제품스팩

Amplifier class

H

Continuous Average Power @ 8 Ohms BCD (Watts)

1250 (x2)

Continuous Average Power @ 4 Ohms BCD (Watts)

2000 (x2)

Continuous Average Power @ 2 Ohms BCD (Watts)

NA

Continuous Average Power Bridged BCD (Watts)

NA

Burst Average Power @ 8 Ohms BCD (Watts)

2000 (x2)

Burst Average Power @ 4 Ohms BCD (Watts)

3625 (x2)

Burst Average Power @ 2 Ohms BCD (Watts)

NA

Burst Average Power Bridged BCD (Watts)

NA

Frequency Response (Hz, +/- 1dB)

20-20,000

Hum and Noise (un / Aweighted -dB)

0.971698113

THD -1kHz- 4 OHMS

0.01%

THD - 20Hz-20kHz, 4 Ohms

less than 0.1%

Slew Rate (V/uS)

50

Damping Factor (30 Hz - 400 Hz @ 8 Ohms)

600

Crosstalk (1kHz / 20Hz-20kHz)

-75 / -60 dB

Input Impedance - Bal/Unbal (Ohms)

20,000/10,000

Input Sensitivity (Vrms) For Full Power Out

1.4 V

Max Voltage Gain (dB)

41

CMRR @ 60Hz (min/typ)

48/56 dB

Stereo / Mono / Bridge (S/M/B)

S/M

Protection

DC,Load,Thermal

Limiter

Peak

High Pass Filter

40Hz, 12dB Octave

Cooling

Dual Internal Fans

Cooling Path

Front to Rear

Fan Filter

2x User Serviceable

Inputs - XLR

2

Inputs - 1/4" Jacks

2

Outputs - Speakon 4-pin

2

Outputs - Binding Post

2

Power Consumption (typ/max)

1800/3000 Watts

Rack Spaces

3

Transformer Type

Toroidal

Exterior Finish

Baked, Black Painted

Dimensions (DWH /D fm ears, inches)

19 x 18.5 x 25 x 17.6

Dimensions (DWH /D fm ears, cm)

48.3 x 47 x 13.3 x 44.7

Weight (lbs / kg)

66.1 / 30

*

Specifications subject to change without notice

AP Series Overview

AudioPro Power Amplifiers

AudioPro AP-Series power amplifiers are built to withstand heavy-duty live sound reinforcement, touring systems or installation. They are the culmination of Yorkville’s forty years of design and manufacturing experience for the music industry, and include features most in demand by audio professionals. They are the ideal choice when high headroom and low distortion are needed, especially when reproducing the dynamic range and clarity of today’s digital recordings.

Yorkville’s AudioPro AP-Series power amplifiers are designed for rock solid performance right down to and below their lowest impedance ratings. An ‘impedance aware’ design strategy deals with the realities of driving typical reactive speaker loads and they address the associated problems such as thermal shutdown, inductive 'snap-back', and premature current limiting. They will easily drive reactive phase shifted loads with no difficulty - even though they are still fully protected from accidental short circuits.

AudioPro amplifiers feature advanced protection schemes including DC current, load, thermal and breaker protection as well as a user-defeatable peak limiter that is transparent below clipping levels. A ‘soft turn-on’ circuit eliminates damage to attached components and prevents nuisance breaker-tripping. The computer-optimized (Silentfan™) front-to-back heat dissipation system incorporates ultra-quiet, variable-speed internal fans and are designed to ensure that excessive thermal stress will not occur. For ease of maintenance and to ensure efficient cooling, the amplifiers are supplied with long-life, faceplate-mounted, user serviceable, air intake filters. Front panel Power, Protect, Activity and Clip LED's are bright and easy to see and all knobs and handles are recessed for safe, easy transportation.

The internal signal path has been optimized and a toroidal transformer is used – both of which serve to reduce hum and noise while keeping weight to a minimum. The two-tier power conversion of the AudioPro AP-Series amplifiers approaches efficiency levels normally associated with switching power supply technology; yet provide the superior transient response and low distortion of the best analog designs.

Inside an AP4020 AudioPro amplifier designs, while unique, are conservative with regard to the power handling capabilities of the output devices. To further assure trouble-free operation, all AudioPro amplifiers undergo a thorough computer-monitored, temperature-cycled, burn-in period to test for any deviation from design parameters.

The back panel features Speakon™ and binding post outputs as well as balanced XLR & ¼" TRS inputs. The peak limiter, subsonic filter, mono/stereo/bridge mode and ground lift switches are also mounted on the back panel. The unique Yorkville Impedance Mode switch (AP1020 & AP2020), also located on the back panel, allows the user to select full output power into two or four ohms for maximum application flexibility.

Sturdy all-steel construction with a baked-on, black finish is used throughout and, for ease of integration, the amplifiers feature reinforced mounting ears and a compact two or three rack-space design.

All AudioPro amps come with Yorkville's standard two-year (even if you break it!) transferable warranty (valid in USA and Canada only).

The Limiter Switch

All AudioPro power amplifiers have a user defeatable limiter circuit switch located on the back panel, next to the input jacks. That limiter is there to protect high frequency loudspeaker components that could be damaged by even small amounts of clipping when an amplifier is being driven close to its maximum output into a full-range cabinet.

When driving subwoofers at the maximum rated output power of the amplifier however, allowing a small amount of clipping at the output of the amplifier is considered an excellent trade-off to get a potential 2dB or 3dB increase in volume, and a small amount of clipping will not damage low frequency drivers. Defeating that limiter allows AudioPro amplifiers to run closer to clipping, and increases the audible volume by potentially as much as 3dB.

Competitive amplifiers without user defeatable limiting either, A) Set their limiting too high to actually offer any practical real-world high frequency component protection, or B) Set their limiting so low that they limit the amplifier’s overall potential headroom.

When comparing AudioPro AP-Series amplifiers to any competitive product, remember to turn the limiter off to feel the increased output when driving subwoofers. However, please note, you should remember to use the limiter when driving full range cabinets. You are less likely to do high frequency component damage with that limiter set to ‘on’.

Choosing the Right Amplifier

The AP-Series has a number of amplifiers that appear to deliver the same power, yet are rated into differing minimum loads. The AP4040 and AP4020, or the AP6040 and AP6020 are prime examples. At a first reading of the specification, the AP4040 and AP4020 may look like the same amplifier, yet the AP4040 delivers 1200 watts per channel into a minimum 4-ohm load (per channel), where the AP4020 delivers that same 1200 watts per channel into a 2-ohm load. Looking at the AP6040 and AP6020, again the same amount of power is delivered into differing minimum loads, or 2000 watts per channel into 4 ohms in the AP6040, 2000 watts per channel into 2 ohms the case of the AP6020.

In the case of the AP2020 and AP1020 power amplifiers, a unique minimum load operation switch on the back of the amplifier allows each amplifier to deliver their maximum power into either a 2-ohm or 4-ohm load for maximum flexibility. A simple user definable configuration allows the AP2020 to deliver 600 watts per channel (400 watts per channel in the AP1020) into either a 2-ohm or a 4-ohm load.

Here is where matching the right amplifier to the right speakers becomes vitally important, and a brief look at the specification charts of each product will help a great deal when choosing an amplifier for your loudspeaker system.

AP6040 & AP6020
The AP6040 / AP6020 amplifiers are Yorkville’s most powerful, featuring a massive toroidal transformer, rugged design and top quality components, ensuring many years of reliable service. Nearly identical in appearance, the AudioPro AP6040 and AP6020 amplifiers each deliver 2000 watts per channel into 4 ohms and 2 ohms, respectively. They have top-of-the-line specifications, ample headroom and are extremely low noise, making them ideally suited for a wide variety of high-power applications.

AP4040 & AP4020
As the workhorses of the AudioPro AP-Series amplifier line, the AP4040 / AP4020 deliver 1200 watts per channel (at 4-ohms in the AP4040, 2-ohms for the AP4020). Sonic quality is excellent while the proven design and quality components assure many years of trouble free performance.

AP2020
The AP2020 weighs a comfortable but solid 35 pounds, fits into two rack spaces, and has the best distortion and noise specifications you will find anywhere. A simple user definable configuration allows it to deliver 600 continuous average watts per channel into either a 2-ohm or a 4-ohm load.

AP1020
The AP1020 is 400 watts per channel, impedance-selectable, professional quality amplifier providing outstanding reliability and performance in a rugged package. The AP1020 is unique in its class, allowing the user to select between two configurations to allow the amplifier to provide maximum possible output into either 4-ohms or 2-ohms, as the user requires for their particular speaker configuration - much like the impedance-switching feature of the AP2020.

AP Series Characteristics

  • Designed for rock solid performance right down to and below their lowest impedance ratings
  • Will easily drive reactive phase shifted loads
  • Advanced protection schemes including DC current, load, thermal and breaker protection
  • User-defeatable peak limiter that is transparent below clipping levels
  • 'Soft turn-on’ circuit eliminates damage to attached components and prevents nuisance breaker-tripping
  • Computer-optimized Silentfan™ front-to-back heat dissipation system
  • Long-life, faceplate-mounted, user serviceable, air intake filters
  • Front panel Power, Protect, Activity and Clip LED's
  • Speakon™ and binding post outputs
  • Balanced XLR & 1/4" TRS inputs
  • Impedance Mode switch (AP800 & AP2020)
  • Sturdy all-steel construction
  • Baked-on, black finish
  • Reinforced mounting ears
  • User defeatable limiter circuit
  • An amp for all needs - Wattage ratings ranging from 160 watts per channel @ 8 ohms (AP800) to 4000 watts bridged @ 4 ohms (AP6020)

970,000원
890,000원
770,000원
1,900,000원
1,150,000원
배송비 : 기본배송료는 0원 입니다. (도서,산간,오지 일부지역은 배송비가 추가될 수 있습니다)  50,000원 이상 구매시 무료배송입니다.
본 상품의 평균 배송일은 3-5일입니다.(입금 확인 후) 설치 상품의 경우 다소 늦어질수 있습니다.[배송예정일은 주문시점(주문순서)에 따른 유동성이 발생하므로 평균 배송일과는 차이가 발생할 수 있습니다.]
본 상품의 배송 가능일은 일 입니다. 배송 가능일이란 본 상품을 주문 하신 고객님들께 상품 배송이 가능한 기간을 의미합니다. (단, 연휴 및 공휴일은 기간 계산시 제외하며 현금 주문일 경우 입금일 기준 입니다.)
상품 청약철회 가능기간은 상품 수령일로 부터 5일 이내 입니다.
상품 택(tag)제거 또는 개봉으로 상품 가치 훼손 시에는 5일 이내라도 교환 및 반품이 불가능합니다.
저단가 상품, 일부 특가 상품은 고객 변심에 의한 교환, 반품은 고객께서 배송비를 부담하셔야 합니다(제품의 하자,배송오류는 제외)
일부 상품은 신모델 출시, 부품가격 변동 등 제조사 사정으로 가격이 변동될 수 있습니다.
신발의 경우, 실외에서 착화하였거나 사용흔적이 있는 경우에는 교환/반품 기간내라도 교환 및 반품이 불가능 합니다.
수제화 중 개별 주문제작상품(굽높이,발볼,사이즈 변경)의 경우에는 제작완료, 인수 후에는 교환/반품기간내라도 교환 및 반품이 불가능 합니다.
수입,명품 제품의 경우, 제품 및 본 상품의 박스 훼손, 분실 등으로 인한 상품 가치 훼손 시 교환 및 반품이 불가능 하오니, 양해 바랍니다.
일부 특가 상품의 경우, 인수 후에는 제품 하자나 오배송의 경우를 제외한 고객님의 단순변심에 의한 교환, 반품이 불가능할 수 있사오니, 각 상품의 상품상세정보를 꼭 참조하십시오.

주소 : 전북 전주시 덕진구 진북동 320-28 | 사업자등록번호 : 402-34-92768
통신판매업신고번호 : 덕진 2007-166 | 개인정보관리자 : | 대표 : 김종성 | 상호명 : 인성미디어
전화번호 : 063-254-4984, 010-9885-4984 | 팩스번호 : 063-254-4986 | 메일 : insungmedia@naver.com
Copyright ⓒ www.insung21.co.kr All right reserved